Orders over $300 ship FREE to 48 States
 

4REEL - Cable Reel Brackets

• Made for a maximum of 4 – 1000’ NMD reels or weight equivalent
• Max Weight: 700 lbs.
• Clip together for compact, easy storage
• Made from galvanized steel
• To be used on 2×4 wood studs only. Not meant for steel studs - more

AC Line Splitter

• Voltage measurement access
• Current measurement rings (x10 and x1)
• GFCI test button
• Outlet connection/polarity indicators
• Current maximum: 15A
• Input voltage: 120V - more

AC Sensor - Non-Contact Voltage Detectors

• Non-contact detection of 50-1000 VAC.
• Senses voltage without metallic contact.
• Outstanding safety instruments that locate defective grounds, energized circuits, induced voltage.
• 2 replaceable “AAA” alkaline batteries included - more

All American Pull Buddy

• Reduces Time and Labor
• Reduces the chance of damaging wires
• Turns wire pulling into a one man job
  - Quantities Available - more info

Allen Head Driver Bit Kit

These high quality hex key allen bits are 6″ long for increased versatility. The 1/4″ shank allows you to use any standard drill or quick change chuck.

Also included in the kit is a 3/8″ socket adapter.

Includes: 5 six inch long Bits, Holder & 3/8" Socket Adapter  - more

Bag Pipers

Bag Pipers - Adjustable, Flexible Airbags -

• Flexible, Inflatable Airbags can be sized to fit a range of conduit sizes
• They can be blown or vacuumed into conduit with most shop vacs
• An inexpensive alternative to other line carriers
• Just 3 sizes fit 1/2” through 6” Trade Size Conduits - more

BEND ALL Cable Bender

Perfectly sized for 4/0, it takes the pain out of 200 amp services or sub feeders. The conductors like it too. The Bend All makes micro adjustable bends without brutalizing the wire.

Fits #3 to 350 MCM conductors. Machined from 6061 Aircraft Aluminum - Fits on a standard 1/2" ratchet. - more

Big E-Z Wheeled Wire Dispenser

The Big E-Z Wire Rack is the Ultra Compact and Collapsible Wheeled Wire Dispenser.

When You're ready to pull wire, assemble the Big E-Z using your Conduit Bender or a scrap piece of 1" pipe (not included) as an axle and you're ready to go.

The Big E-Z utilizes the same design and great features as the original E-Z Roll while allowing you to dispense larger wire spools.

Holds up to 32" Diameter Reels - 300 lb Load Tested - more

Booty Pack

Disposable Booty Covers, Gloves and Respirator -

BullDog Wire Bending System

BullDog Benders -

Features:

• The Original and Pro BullDog Benders bend up to 500 MCM
• The Big Daddy BullDog Bender bends 500 to 750 MCM
• Available with knurled or smooth dowels
• MADE IN THE USA  -  more

Bumper Balls

Bumper Balls Flexible Drill Bit Guide -

Ever had a Drill Bit go off Course? Bumper Balls keep your Flexible Drill Bits centered where they should be.

No More:

• Bit Walking
• Nail Hitting
• Wall Patching
• Carpet Replacing -  more

Butt Pouch Pocket Pro, the Pocket Tool Holder

+
PAPA GRANDE

-

Butt Pouch is the Tool Pouch that fits right in your pocket! No Belt required.

Large snap loop for attaching to your belt if preferred. Quick to put on and comfortable too. Made of ballistic nylon -

3 Models to choose from. - more

Rackatiers Heavy Duty Tool Belts, Bags & Totes
 

Cable Chase Wire Support Brackets

The easiest and safest way to route wire and cable

The Cable Chase Wire Support Brackets are designed to provide a straight, clean path for wires with no obstructions.

The brackets allow you to greatly reduce friction and stress on wires being pulled through the holes due to the hole design. - more info

CableStik Multi-Purpose Cable Dispensing System

CableStik Multi-Purpose Cable Dispensing System -

• Fast, installs in seconds
• Requires no tools for installation
• Very compact, stores easily
• Max Load 130lb
• Stud-Mounted, Free-Standing and Hitch / Vehicle Mounting Capability more info

Carbide Tipped Hole Saw Kit for Wood and Drywall

Perfect for cutting through Wood and Drywall

Includes:

• 7/8", 1-1/8", 1-3/8", 1-3/4", 2", 2-1/2" Hole Saws
• Large and Small Arbors
• Custom Carrying Case - more

Carbide Tipped Steel Hole Cutter Kits

• Great for Cutting mild steel & stainless steel
• Split point pilot drill
• Flange prevents over drilling
• 4pc Kit: 7/8", 1-1/8", 1-3/8" + Spare Pilot Drill
• 8pc Kit:  7/8", 1-1/8", 1-3/8", 1-3/4", 2", 2-1/2" + 2 Spare Pilot Drills
  - more

Chip Catcher - The Metal Shavings Trapper

The Chip Catcher clamps to either the bottom or top of a metal surface using rare earth magnets to catch the metal shaving as you drill, leaving you with a quick and easy cleanup.

• Rare earth magnets stick to any metal surface

• Protect valuable components from metal shavings  - more

Clip Whacker Beam Clamp Installation Tool

The Clip Whacker is specifically designed to easily and safely install beam clamps/clips.

• Rare Earth Magnet holds the clip in place
• Fits multiple sizes of Beam Clamps/Clips
• No more flying clips or sore fingers!
• Saves Time and Money!
• Made in USA! - more

Co-Pilot Hole Saw Adapter

Tired of your pilot bit dancing around inside an existing hole you are trying to expand upon?

The Co-Pilot bit allows you to stack two hole saws on top of each other utilizing the smaller hole saw as the pilot bit it slips perfectly into the existing hole.  - more

Copper Wire Stripper / Wire Stripper Jr.

Recover copper wire and aluminum quickly and easily with these money making machines

• Hardened one piece blade
• Strips solid core or stranded wire
• Fully adjustable wire guide
• Blade easily re-sharpened - more

Croc's / Croc's Jr. Needle-Nosed Wire Strippers

Croc's™! What a beautiful stripper. -

• Needle nose tips
• Strips conductor sizes from #10 down to #22 AWG (Crocs)
  8 - 22 AWG (Croc's Jr.)
• Large cutting blades for easy general purpose cuts - more

Dirt Bag - Electrical Safety Drilling Tool

The Dirt Bag is specifically designed to eliminate unwanted metal shavings from spreading throughout a panel.

A simple, portable tool the will save you time and headaches down the road.

• Easily attaches to metal surfaces
• Made from non-conductive material
• Not to be used on live panels  - more

DRILLER'S Dust Bowl

You may enjoy a face full of drywall dust but your customers might not!

The flexible DRILLER'S Dust Bowl compresses and traps dust and debris as you drill. It fits your drill and holesaw without any adjustments.

Put an end to 'unprotected holesawing' Fits Hole-Saws up to 8" diameter. - more

'Electrician's Kit'

The 'Electricians Kit' has a great selection of Blades that any Electrician needs and would use on a regular basis!

Featuring coarse and fine tooth blades as well as Bi-Metal blades, this Kit has everything you need for almost all Applications.

Includes 2x Bi-Metal Blades and 2x Wood/Plastic Blades - more

ER-Go50 - Ergonomic Wire Spool Carrier

Ergonomic carrier specially designed for the manual transportation of wire spools (electric wiring, steel cable, chain, etc.)

• Carry Wire Spools with one hand
• Just slip it in and Lift!
• Lift center handle to release.
• Weight capacity: 50Lbs. - more info

Extendo Nut Driver - Hollow Shank Nut Driver Kit

Adapt a standard 1/2″ EMT conduit into an extension nut driver for threaded rod.

Utilizing the concept of a hollow shank nut driver, The Extendo gives you the flexibility to cut the 1/2″ EMT any length you need to drive the nut up the full length of threaded rod.

Save yourself time and money with this extension nut driver kit. - more

E-Z Roll Wheeled Wire Rack

Most wheeled wire dispensers are too big for your truck and they only hold little wire spools. The E-Z Roll Wire Rack knocks down in seconds and handles reels to 18 inches. (150 lb. Load Tested). Use a conduit bender or scrap of 1" EMT (not included) for an axle/handle.

The E-Z Roll is big enough to handle 1000' rolls of Romex., but small enough to fit in a Job Box.  Simple, Effective, Rigid Steel Construction and Light-weight Design. - more

Ferret WiFi Wireless Inspection & Cabling Tool / Ferret Stick

FiberSnake Non-Conductive Duct Rodders

FiberSnake Non-Conductive Fishtapes and Duct Rodders -

Fiberglass reinforced plastic fish tape with durable low-friction polyamide coating. Includes a light and durable steel frame with anti-corrosion surface treatment.

Available in a variety of lengths. - more

Fish Heads Fish Tape End Repair Kit

Easily Repair and Improve your 1/8" Fish Tape with the Fish Heads FishTape Repair (and Improvement) Kit!

Tired of getting a Fish Tape snagged or breaking? Ever think there's got to be a better way?

Give the Fish Heads FishTape Repair Kit a try! - more

Flex Flyer FishTape Repair / Improvement Kit

1/2" + 3/4" Sizes

EASILY FIX AND IMPROVE BROKEN FISH TAPE ENDS

The Flex Flyer features a quick change swivel head that installs on the end of a fish tape in 20 seconds by twisting the fish tape with 2 pairs of pliers. The loop technology allows the leader to move smoothly through all types of conduit including flex.

The standard 1/4" - 28 threads allow for other types of leaders to be attached to the quick change base. - more

Flex Puller - MC Cable Pulling Tool

Thread a Flex Puller onto an MC Cable, hook to your string or fish tape and pull! The EASY way to pull MC Cable!

• Easily screws onto exterior of 1/4" and 3/8" MC cable
• Provides a hook to pull MC cable through hollow and insulated walls and ceilings
• Can be used on #14, #12 and #10 MC Cable
• Package of 2  - more

H2 Homer Helpers Cable Support Brackets

The H2 Homer Helpers are intended to support multiple NM-B, MC and Low Voltage cables in electrical home runs. They will greatly reduce labor time and eliminate the use or need for staples.

• Quickly and easily supports multiple electrical cables.
• Holds up to 24 cables with one support.
• Greatly reduces labor time.  - more

Head Light

• 3 Modes: High, Low & Strobe
• Powerful COB LED bulb illuminates up to 20m
• 150 Lumens output on High /
  50 Lumens on Low
• Runtime: High - 4 Hours, Low - 12 Hours
• 3.7v Rechargable Battery & USB Cable included  - more

HOLDSaBIT Drill Mounted Bit Holder

The ingenious HOLDSaBIT slips on or off a drill in seconds. Simply pull one loop over the front of the drill and pull the second loop to the back of the drill.

The HOLDSaBIT will hold any 1/4″ hex shank item as well as pencils, nut drivers and hex shank drill bits. Tips and bits are easily inserted and removed.

The HOLDSaBIT keeps your drill bit accessories “Where you need them – When you need them. - more

Hole Pro Multi-Function Twin-Blade Hole Cutter

Cuts perfect circles in Sheetrock & Wood Every Time!

• Quick, easy, clean cutting of holes in ceilings, walls and floors
• Cuts holes 1-7/8" to 17" diameter, in ceilings, walls and floors.
• Cuts Plywood, Sheetrock,  and Fiberglass
• Cutting Depth to 1-3/16"
• Ball Bearing Design for Job-Site durability - more

Hooker Pipe Wrench Adapter

Every RACK-A-TIER needs a HOOKER! - RACK-A-TIERS have always had a "pipe vise" capability with the 'V' notches. They set out to improve this function and succeeded beyond expectation.

A set of RACK-A-TIERS with a HOOKER pipe wrench adapter can stand in for a tripod or bench mounted pipe vise plus it's faster and easier to use. The HOOKER is far lighter, less expensive and fits all RACK-A-TIERS. - more

Hoppy Bender - EMT & Rigid Conduit Benders

Impact Driver Bits

These impact rated bits will hold up to the rigorous strains caused by using an impact drill.

Color Coded for ease of use

Robertson Square Drive, Phillips & Double Ended Bits - more

The Javelin - All in One Extension Kit

Extend your Drill Bits up to 10 Feet!

Just cut a 3/8" - 16 threaded rod any length you need, and attach the Javelin pieces to each end.

Use with Holesaws to 1-1/8" and any tool with a 1/4" hex shank, including spade bits, driver bits, nut drivers, drill bits and more...

Fits 3/8" Drill chucks - more

Jet Level - Magnetic Conduit Level

Measure for Boxes in a SNAP with the etched base template!

• 4 powerful Rare Earth Magnets
• CNC Milled Accuracy from Billet 6061 Aluminum Alloy
• Extra large "V" grooved edge remains parallel on curved surfaces up to 10" in diameter
• 4 Precision Vials - 0, 30, 45 and 90 degrees
• Horizontal Vial visible from both sides and Top
• Water and Shock Resistant
• Designed for portability, efficiency and durability  - more

The Jimbo Wire Pull Bracket

The Jimbo – Wire Pull Bracket helps to eliminate cable snags and damage over sharp edges and ceiling grid.

• Set up multiple brackets making a temporary cable raceway to avoid catching or snags
• Consolidate cables to the best angle for ease of pulling
• Multiple ways to attach and configure to match the situation
• Pull hard around corners and through structural steel  - more

KO Killers - Plastic Knockout (KO) Fillers

No more tools, hammers, flying metal fillers, exploding buss bars, etc. Needing no tools is a big plus, especially when working space is tight. They go in easily and stay in. KO Killers fit all electrical boxes, including heavy wall cabinets.

Available in 1/2” through 2” trade sizes. - more

Self-Leveling Vertical Laser Plumb Bob

Looking for a better way to lay out complex ceilings and high bays? - Tired of trying to measure ceiling work from the top of a ladder? - The RACK-A-TIERS^® Laser Plumb Bob enables you to lay out overhead work on the ground and then quickly transfer the measurements to the ceiling.

Factory aligned laser module calibrated to precise 0.15° accuracy - Magnetic damping for quick stabilization. - more

LaserLine Pull String Installation Tool

LaserLine will accurately install (shoot) a pull line up to 120ft. - through most web trusses, across suspended ceiling systems, over hard to move objects, under sub-flooring or in any limited access areas like those found in most offices and commercial building structures. - more

LB Wire Guide

LB Wire Guide -

A ‘SHOE HORN’ FOR 2” LB’S

• For PVC LB fittings & adaptable to most metal LB’s
• One man conductor installation
• Faster conductor installation
• Installs in two positions to fit both ‘Ends’ of the LB
• Helps prevent Conductor Damage - more

Level Jack - Low Voltage / Datacom Plaster Ring

Alignment tabs reach across wood/metal studs to level low voltage outlets with A.C. boxes. No tape measure / No level required.

Locknut Wrench

How many locknuts have you bashed with your flat blade screwdriver?

The Locknut Wrench allows you to tighten locknuts quickly and works great in tight spaces. Available in 3 sizes: 1/2", 3/4" + 1"

They belong in every Electricians Tool Pouch - more

Mag Daddy Magnetic Cable Fasteners

The Mag Daddy - Magnetic Cable Holders and Tie Mounts are ideal for strapping wire to metal areas. Available in a variety of types and sizes to best suit your needs.

Attach to: Steel, Beams, Purlins, Ceiling Decks, Drop Ceiling Channels, Metal Joists, Frame Rail, Screw Heads, Metal Washer, etc. - more

Magnepull

This new version has a much stronger magnet and a smoother rolling surface. - more

Magnetizer / DeMagnetizer

Magnetizes or demagnetizes driver bits, tools and small steel parts instantly!

- more

Malco Reversable Hex Driver Bits

Instantly change between hex sizes with these magnetic, one of a kind, dual-sided hex driver bits.

Dual Sided Bits available in: 1/4" & 5/16" and 5/16" & 3/8"

The tested torque of either side of the bit is equal to that of a standard one-piece driver bit. - more

Nut Blaster Universal Wire Connector Tool

2 Sizes - fits all brands of Yellow, Tan, Red, Large Gray and Blue Twist on Wire Connectors!

• Prevents Sore Fingers & Cramping Hands
• Fast, Easy Installation
• Works in all quick release adapters, Power Screwdrivers & Drills
• Made in USA - more

Nut Snugger

Utilizing Magnets the Nut Snugger allows you to install and tighten a Locknut without assistance when the connector is out of reach.

• Available for 1/2" and 3/4" Locknuts
• Can be used with Adjustable Wrench, Tongue and Groove Pliers, 3/4 Box or Open End Wrench and 3/8 Drive Ratchet (not included)
• Made in USA - more

OverDRIVE Fast Boring Bits

OverDRIVE Fast Boring Bits are designed for Cordless Drills to extend Battery Life while maintaining Fast, Smooth, and consistant cuts.

• Clean Cutting for finished holes with minimal "Blowout"
• Induction-Hardened steel construction and precision ground cutting edges for durability and accuracy
• Performance superior to Spade Bits - more

Panel Buddy Knockout Remover Kit

Tired of Trying to Remove Knockouts on Installed Panels?

Panel Buddy Knockout Kit removes knockouts on installed Electrical, Security, Alarm and Datacom Panels (both lipped and unlipped) without causing damage to sheetrock that must be repaired. - more

Penguin Puller

The Penguin Puller Sr. and Jr. are revolutionary new tools designed to aid in easily pulling in large cables.

• Penguin Puller Sr. - 3/0 to 350 MCM Copper or Aluminum
• Penguin Puller Jr. - 1/0 to 4/0 Copper or Aluminum
• 5,000 lbs. MAX PULL STRENGTH - more

Pipe Spring PVC Conduit Bender

Add a little brute force and you can bend 1” too. Believe it! - more

Plugfones Hearing Protection Earplugs & Earphones

Earplugs & Earphones in One! -

Finally, innovative hearing protection combined with music! AT WORK: Ear plugs certified to the ANSI noise reduction standards up to 30 dB. Built with Tuff Cord tear resistant wires. - more

PlugMaster Multi-Function Electrical Safety Tool

The PlugMaster combines a full function dual-outlet circuit tester with 220V detection and multiple direction bubble-levels.

• Acts as horizontal and vertical level
• Use for diagnostics
• Perform quick wiring checks
• Panel identifies conditions shown by LED indicators
• Removable side panels cover outlet during insertion
  - more

Polyester Fish Tapes in Cases

These non-conductive, light-weight fish tapes in cases are perfect for line or low voltage fishing. Available in two or three strand depending on the length of the Pull

• Available in 2 Strand (49.2 ft - 15m)
  or 3 Strand (98.4 ft - 30m) - more

ProJob Multi-Pocket Work Pants

ProLock Locking Cord Connector

ProLock Locking Cord Connectors hold securely and provide 80 lbs of pull strength keeping your cord connections secure!

The patented ProLock locking cord connector was designed to prevent all extension cords with standard straight blade 15A – 120V plugs and connectors from pulling apart. - more

PulLee Wire Roller

Slim, but Strong Steel Roller fits in your Box for Smooth and controlled Wire Pulling

• Spring-Loaded Tips keep it locked in place
• Reusable

Q-Bit Outlet Box Hole Saws

The Q Bit is the recently designed tool that makes cutting in-wall boxes fast and easy!

The Q Bit fits to nearly all Multi-tools, and quickly turns them into the square saw blade you need!

If you are required to cut square holes in sheet rock on any occasion the Q Bit Blade will take all the labor and hassle out of it immediately! - more

RACK-A-TIERS Wire Dispensers

As a wire dispenser only, RACK-A-TIERS are hard to beat but they have many other uses. It's a good thing they're tough because they get a lot of use and you'll have them for a long time.

No moving parts, won't rust, rot, scratch your trunk, bash the doorframe, and they float. Nice and compact, RACK-A-TIERS earn their place in your truck. (sold in pairs) - more

Racksy Pad Gel Knee Pads

Improved!

RACKY Bits - Color Coded Drive Bits

COLOR coding? It’s so simple but it works.

Racky Bits are easier to use and harder to lose and they make your job easier.

If that’s not enough, our genuine Robertson® RACKY BITS have hardened tips that fit better and last longer. - more

Racky Bit Kits

The Racky Bit Finishing Kit features all the colour-coded driver bits you need for finishing a house or condo. Includes 6-32 and 8-32 tapping bits for when those cheap screws break on you. - more

Racky Van Magnets

Got a disorganized van?

Snap some Racky Van Magnets into place to hang tools, material, etc. to keep your vehicle nice and tidy.

3 different weight ratings to best suit your needs  - more

REEL-END - Wire Spool Repair

How many broken spools in your shop? A few? A bunch? There's gold in them thar rolls but how do you get at it? Fix them with the Reel End. Pays for itself with the first roll saved and it's reusable again and again.

The Reel End fits plastic spools #10 through #18 gauge. A real money maker. "Who says you can't put those pieces back together?" - more

Reemer Bits

Ream your pipe and tighten your couplings and connectors with the same tool!

• Tighten your connectors and couplings
• #2 Robertson and #2 Phillips driver bit
• Central Area Reams all sizes of conduit
• Fits regular and quick release drill chucks - more

'Rapid Fire' & 'Tom Two Way' Romex Connectors

Romex Connectors -

Doing some renovation work? The TT-500 (aka "Tom Two Way") also installs from the inside of the box after the wire is fished in. Ingenious.

The RAT 500 and RAT 750 feature the same quality and large wire capacity but install from the outside for use in new construction. If you like the best, try these. - more

Ropematic Pro Rope & Fish Tape Puller

The Smart (and easy) way to pull Rope, FishTapes and more...

Stop wrapping Rope around hands and wrists... put away the pliers for pulling Fish Tapes - Just slip the Ropematic Pro over the Rope or Fish Tape and pull!

The Ropematic Pro locks down on the Rope or Fishtape as you pull towards you, and releases as you slide it forward for the next pull.

Stop hurting those hands and wrists...  - can increase your pulling power dramatically!  -more

Round Multi-Tool Hole Saws

Cut holes with perfect precision!

The first round multi-tool hole cutter to hit the market is available in 2 sizes: 3 3/8 and 4 1/4 inch.

Cut holes in drywall for your recessed lights quickly and effectively using your oscillating multi-tool. - more

Sharp Pog Multi-Tool Blade Sharpener

The Sharp Pog allows you to quickly and effectively sharpen multi-tool blades using only your battery drill.

Stop throwing out dull multi-tool blades, keep them sharp with the Sharp Pog! - more

ShinMate Ladder Guard

Take the stress off of your knees, shins and legs with the Comfortable ShinMate Ladder Guard.

The ShinMate Ladder Guard was designed by a tradesman for tradesmen. Electricians, painters, carpenters, window washers or anyone who works on ladders for hours on end will benefit from the ShinMate. - more

Sluggo-Ox - Ultimate Ground Rod Driving Tool

SLUGGO-OX™ is the revolutionary new tool that’s taking the industry by storm.

• Incredibly strong, made of 3” hot-rolled, heat-treated, hardened steel
• 3 1/2” bore to accept 3/4” and 5/8” ground rods
• 80% more striking surface
• One piece, light-weight (7lbs.)
• Avoids 'Mushrooming'
• Yellow zinc chromate surface to deter rust -more

Snatch Strap Wire Puller

Time is money and when you think about it, a lot of time is spent stripping, taping and untaping wire for fishtape pulls. The SNATCH STRAP gives you back this time. Because it staggers the wire, you can pull more conductors with less effort.

Because SNATCH STRAPS can be daisy chained, you can easily drop wire groups at boxes along the pull. Brilliant! - Package includes 3 Snatch Straps. - more

Staple Shark Multi-Purpose Tool

The Staple Shark is a must-have for anyone who does Residential Installation and Remodel work

• Easily removes staples of all sizes without damage to cables
• Made of Hardened Steel
• Multi-Purpose use as a Staple Remover, Prybar, Nail Puller, Ruler, Square, and even a Bottle Opener! - more

The Stick - Stud Mounted Cable Dispenser

The Stick installs quick and easily to any standard stud. Its compact design allows for easy storage once the job is complete.

• Weight capacity: 200Lbs.
• Maximum 15" reel width - more

Stud Ball

The Stud Ball is a protected magnetic stud finder that will out perform other types of magnetic stud finders on the market.

Unlike other steel stud finders, the Stud Ball can detect metal through 1/2" or 5/8" drywall or other thicker building materials.

Will also work through ceramic tiling and up to 3/4" plywood paneling.

Mfg Note: Will find 40 or more steel studs on a wall with 5/8" drywall in less than a minute. - more

Stud Buddies - Steel Stud Bushings

No Tools Required - Faster, Easier to Use!

• One Piece
• One Hand Installation
• Fits all standard Steel Studs and Punches
• Fire Rated V.O.
• 2 Styles, Round & Square (70% more cross sectional area) - more

The Puck - Ground Clamp Socket Tool

A New Solution for Installing Ground Clamps!

• Multi-purpose – works for eye-bolt and T-handle
• Fits common 1/2 inch drive socket wrenches
• Allows ground clamps to be quickly, easily, and more securely installed in hard-to-get-to places
• Provides proper leverage on short T-handles - more

Thomas Wheeler Coil Spinner / Wire Spool

This easy-to-hang wire dispenser allows fast, twist-free Romex, MC cable or flex pulling. -

Most coil dispensers are too big, cumbersome and expensive. Not this one. The Thomas Wheeler knocks down (folds down flat) and sets up in seconds, hangs on 2x4, in the trusses, above tee bar or on a ladder. Light, simple, rugged and it really works. A great value! - more

Tug-Wise Reel Management System

Eliminate extra costs for labor and expensive reel stands.
 - handle Reels up to 6,000 lbs! - more

Ultimate AC Sensor - Non-Contact Voltage Detector

• Non-contact detection of 50-1000 VAC.
• Senses voltage without metallic contact.
• Outstanding safety instruments that locate defective grounds, energized circuits, induced voltage.
• 2 replaceable “AAA” alkaline batteries included - more

U-Phase Wire Markers

Quickly and conveniently use the UPhase wire marker to color cords and wires for fast and easy organization.

Easily and permanently mark wires inside of panels.

Can be used with line or low voltage cables. - more

V-Cutter Cable Stripper Attachment

One of the smartest inventions to come to market this decade is the V-Cutter.

This simple little blade attaches to most wire strippers and allows you to strip cable sheathing in or outside of the Electrical Box!

(Wire Stripper not Included) - more

Wire-Pod Portable Cable Dispenser

The Wire-Pod is a compact, portable dispenser designed specifically for coils. This handy device will work with NMSC (NM), AC, and Flex coils.

• Opens for use and folds away for easy storage
• Compatible with NMSC (NM), AC and Flex coils
• Weighs less than 3 LBS.
• Made in the USA

Wire Tub - Wire Dispenser AND Rewinder

All coil dispensers dispense but this one REWINDS wire as well. Over-runs can be wound back, old wire salvaged and re-installed. And it's fast. No hanging or mounting, the WIRE TUB just sits on the floor.

Handles Flex, Romex, MC, etc. Same tough plastic as RACK-A-TIERS. Awesome!
- Big 24" diameter capacity. - more

Wire Vortex

Like having an extra pair of hands on the Job! -
Pays for itself the first time you use it!

• Protect wires from damage while pulling
• Fits 4" Square Boxes
• Can be used in all 4 Directions
• Flip it over to fit standard (shallow) or deep boxes
• Made of Strong, Impact-Resistant Plastic
• Easy on and off - more